Latency issue in VM

For discussion of the Voltage Modular synthesis ecosystem.
farbstoff-fabrik

Latency issue in VM

Post by farbstoff-fabrik »

I noticed that - after exporting wave files from FL Studio - voltage modular has 0,005 seconds of delay.

I tested against a sample (short closedhihat) and it shows up at 0,000 and VM at 0,005.
I tested VM against VST Polysix of Korg. Korg shows at 0,000 and VM at 0,005.
I tested VM in reaper (to rule out if FL was the problem), VM starts again recording at 0,005.
I tested different patches, a basic synth (oscillator>envelope>amp), several synths with internal VM sequencers.
time-issue-2.JPG
time-issue-2.JPG (63.4 KiB) Viewed 3223 times
time-issue.JPG
time-issue.JPG (80.76 KiB) Viewed 3223 times
I think this is quite a issue. How can I fix this?
farbstoff-fabrik

Re: Latency issue in VM

Post by farbstoff-fabrik »

I have consulted two other users, one of the uses Ableton, and they both experience this issue. I guess the pdc time of VM is 0,005 off.

The problem arises when you try to export a pattern to a loop. It doesnt loop then. When it starts 0,005 later the end is also 0,005 short. In other words, you miss 0,005 in the end. It might be less significant because its just 0,005 but still you can tell the timing isnt correct.

Could you please look into this issue.

Thanks in advance,

-Matt
dasmode
Posts: 27
Joined: Sun Jun 16, 2019 5:52 am

Re: Latency issue in VM

Post by dasmode »

    Last edited by dasmode on Thu Jan 21, 2021 8:35 am, edited 1 time in total.
    dasmode
    Posts: 27
    Joined: Sun Jun 16, 2019 5:52 am

    Re: Latency issue in VM

    Post by dasmode »

      Last edited by dasmode on Thu Jan 21, 2021 8:35 am, edited 1 time in total.
      farbstoff-fabrik

      Re: Latency issue in VM

      Post by farbstoff-fabrik »

      Very strange...

      A few questions:

      1. Are you running a win or mac setup?
      2. Which versions of VM are you using?

      Thanks in advance!

      Matt
      dasmode
      Posts: 27
      Joined: Sun Jun 16, 2019 5:52 am

      Re: Latency issue in VM

      Post by dasmode »

        Last edited by dasmode on Thu Jan 21, 2021 8:35 am, edited 1 time in total.
        farbstoff-fabrik

        Re: Latency issue in VM

        Post by farbstoff-fabrik »

        Ok - long story short. When I make a new patch in a blank cabinet: no problem occurs. When I recall a preset patch, I get that 0,005 timing issue.
        Also with Cherry Patches. I tested that just to rule out my own bad cabeling.

        I also downgraded FL Studio to rule out that too becasue I never noticed the timing issue before.

        I am totally lost. I just wasted 2 hours this evening to try and find out what's happening.

        @dasmode could you do me a favour and do the same test using a preset patch you saved?
        Attachments
        presetrecall.JPG
        presetrecall.JPG (61.9 KiB) Viewed 3144 times
        dasmode
        Posts: 27
        Joined: Sun Jun 16, 2019 5:52 am

        Re: Latency issue in VM

        Post by dasmode »

          Last edited by dasmode on Thu Jan 21, 2021 8:34 am, edited 2 times in total.
          farbstoff-fabrik

          Re: Latency issue in VM

          Post by farbstoff-fabrik »

          Are you using the vst2 or vst3 version? I am really puzzled. :o :roll:
          farbstoff-fabrik

          Re: Latency issue in VM

          Post by farbstoff-fabrik »

          LOADED-PATCH-UPPER-LOWER-NEW-DESIGN.JPG
          LOADED-PATCH-UPPER-LOWER-NEW-DESIGN.JPG (57.81 KiB) Viewed 3140 times
          I tested it again. Upper (left) hannel is a preset patch from cherry, lower is a just designed simple synth. I am clueless.
          Post Reply

          Return to “Voltage Modular”