Page 1 of 2

Latency issue in VM

Posted: Mon Jan 04, 2021 11:03 pm
by farbstoff-fabrik
I noticed that - after exporting wave files from FL Studio - voltage modular has 0,005 seconds of delay.

I tested against a sample (short closedhihat) and it shows up at 0,000 and VM at 0,005.
I tested VM against VST Polysix of Korg. Korg shows at 0,000 and VM at 0,005.
I tested VM in reaper (to rule out if FL was the problem), VM starts again recording at 0,005.
I tested different patches, a basic synth (oscillator>envelope>amp), several synths with internal VM sequencers.
time-issue-2.JPG
time-issue-2.JPG (63.4 KiB) Viewed 859 times
time-issue.JPG
time-issue.JPG (80.76 KiB) Viewed 859 times
I think this is quite a issue. How can I fix this?

Re: Latency issue in VM

Posted: Wed Jan 06, 2021 1:26 pm
by farbstoff-fabrik
I have consulted two other users, one of the uses Ableton, and they both experience this issue. I guess the pdc time of VM is 0,005 off.

The problem arises when you try to export a pattern to a loop. It doesnt loop then. When it starts 0,005 later the end is also 0,005 short. In other words, you miss 0,005 in the end. It might be less significant because its just 0,005 but still you can tell the timing isnt correct.

Could you please look into this issue.

Thanks in advance,

-Matt

Re: Latency issue in VM

Posted: Wed Jan 06, 2021 5:00 pm
by dasmode

    Re: Latency issue in VM

    Posted: Wed Jan 06, 2021 5:11 pm
    by dasmode

      Re: Latency issue in VM

      Posted: Wed Jan 06, 2021 5:36 pm
      by farbstoff-fabrik
      Very strange...

      A few questions:

      1. Are you running a win or mac setup?
      2. Which versions of VM are you using?

      Thanks in advance!

      Matt

      Re: Latency issue in VM

      Posted: Wed Jan 06, 2021 5:52 pm
      by dasmode

        Re: Latency issue in VM

        Posted: Wed Jan 06, 2021 8:30 pm
        by farbstoff-fabrik
        Ok - long story short. When I make a new patch in a blank cabinet: no problem occurs. When I recall a preset patch, I get that 0,005 timing issue.
        Also with Cherry Patches. I tested that just to rule out my own bad cabeling.

        I also downgraded FL Studio to rule out that too becasue I never noticed the timing issue before.

        I am totally lost. I just wasted 2 hours this evening to try and find out what's happening.

        @dasmode could you do me a favour and do the same test using a preset patch you saved?

        Re: Latency issue in VM

        Posted: Wed Jan 06, 2021 8:35 pm
        by dasmode

          Re: Latency issue in VM

          Posted: Wed Jan 06, 2021 8:40 pm
          by farbstoff-fabrik
          Are you using the vst2 or vst3 version? I am really puzzled. :o :roll:

          Re: Latency issue in VM

          Posted: Wed Jan 06, 2021 10:02 pm
          by farbstoff-fabrik
          LOADED-PATCH-UPPER-LOWER-NEW-DESIGN.JPG
          LOADED-PATCH-UPPER-LOWER-NEW-DESIGN.JPG (57.81 KiB) Viewed 776 times
          I tested it again. Upper (left) hannel is a preset patch from cherry, lower is a just designed simple synth. I am clueless.